Drills

Reversible pneumatic drill The pneumatic drill is ideal for pilot hole drilling in a production line. The drill has non-variable speed set to 1800 rpm. A compressor is required with an air flow delivery of at least 106 l/min at 6.3 Bar to make use of the drill. Make sure that an in-line lubricator is fitted with pneumatic oil (AT OIL).....

AirCraft Chuck 10mm (3/8") for Air Drill 10mm Reversible 1800rpm (AT0005-31) At a Glance: 10mm (3/8") replacement drill chuck for AirCraft 10mm reversible air drill—restores solid bit grip and smooth drilling control. A worn chuck turns a good air drill into a frustration machine—bits slip, wobble increases and accuracy goes out the window. The AirCraft AT0005-31 10mm (3/8") chuck is a replacement chuck for the AirCraft 10mm reversible 1800rpm air drill, designed to clamp securely and hold y..

AirCraft Air Drill Service Kit O-rings and Seals (2,3,5,7,16,24) for AT0005 (AT0005-SK01) At a Glance: Complete O-ring and seal refresh kit for the AirCraft AT0005 air drill—targets common leak points and worn seals. When an air drill starts losing power, free-spinning, or hissing like a kettle, the culprit is often tired seals. The AirCraft AT0005-SK01 service kit supplies the O-rings and seals referenced as parts (2,3,5,7,16,24) for the AT0005 air drill, helping you restore proper sealing,..

AirCraft Air Drill Service Kit Bearings (17,29) for AT0005 (AT0005-SK02) At a Glance: Bearing replacement kit for the AirCraft AT0005 air drill—helps eliminate rough running, excessive noise and vibration caused by worn bearings. Bearings are the quiet workhorses inside your air drill—until they wear, then everything gets louder, rougher and less precise. The AirCraft AT0005-SK02 service kit supplies the replacement bearings referenced as parts (17,29) for the AirCraft AT0005 air drill. Idea..

AirCraft Air Drill Service Kit Trigger Comp. (4,6,8,9,10-12) for AT0005 (AT0005-SK03) At a Glance: Trigger component service kit for the AirCraft AT0005 air drill—ideal for fixing sticky triggers, inconsistent throttle response or air leakage around the trigger/valve area. When an air drill starts acting moody—sticky trigger, uneven speed control, or a little hiss where it shouldn’t—there’s a good chance the trigger/valve parts are worn, dirty or damaged. The AirCraft AT0005-SK03 service kit..

AirCraft Air Drill Service Kit – Main Body Comp. (1/13-15/35) For AT0005 (AT0005-SK04) At a Glance: Main body component service kit for AirCraft AT0005 – refreshes housing/control-related parts referenced as 1/13-15/35. If your AirCraft AT0005 air drill has taken a few knocks, feels loose in the hand, or the controls and body parts are starting to look (and feel) tired, the AT0005-SK04 service kit is the smart fix. This Main Body Components kit targets the external and control-side parts of th..

AirCraft Air Drill Service Kit – Rotor & Cyl. (18/19/21-23) For AT0005 (AT0005-SK05) At a Glance: Rotor and cylinder service kit for AirCraft AT0005 – replaces parts 18/19/21-23 to restore smooth, consistent drill performance. When a pneumatic drill starts losing punch, running rough, or struggling to maintain speed, the usual suspects live in the motor group. The AirCraft AT0005-SK05 service kit is a targeted rotor & cylinder refresh designed for the AirCraft AT0005 air drill, covering compon..

AirCraft Air Drill Service Kit – Gear & Rot. Axle (25-27) For AT0005 (AT0005-SK06) At a Glance: Gear and rotational axle service kit for AirCraft AT0005 – replaces drive components referenced as 25-27 for smooth, efficient power transfer. When an air drill starts sounding “gritty”, slipping under load, or losing that crisp torque delivery, the drivetrain is usually crying for attention. The AirCraft AT0005-SK06 service kit is built to refresh the gear and rotational axle components for the Air..

AirCraft Air Drill Service Kit – Gear Ring & Fixing Ring (28/30) For AT0005 (AT0005-SK07) At a Glance: Gear ring and fixing ring service kit for AirCraft AT0005 – replaces parts 28 and 30 to keep the drivetrain tight, aligned, and smooth. A ring gear that’s worn, chipped, or no longer sitting perfectly can turn a good air drill into a noisy, uneven, power-wasting machine. The AirCraft AT0005-SK07 service kit is designed to refresh the gear ring and fixing ring on the AirCraft AT0005, covering ..

AirCraft Air Drill Service Kit – Chuck & Key (32-34) For AT0005 (AT0005-SK08) At a Glance: Chuck and key service kit for AirCraft AT0005 – replaces parts 32-34 to restore strong bit grip and smooth tightening. A worn chuck turns drilling into a constant fight—bits slip, run off-centre, and tightening never feels quite “right”. The AirCraft AT0005-SK08 service kit replaces the chuck and key components for the AirCraft AT0005, covering reference positions 32-34. It’s the go-to refresh when your ..

AirCraft Air Drill Service Kit – Rotor Blade 5pc Set (20) For AT0005 (AT0005-SK09) At a Glance: 5-piece rotor blade (vane) set for AirCraft AT0005 – replaces part 20 to bring back crisp power and smooth air-motor operation. Rotor blades (also called vanes) are the hardworking “muscles” inside the air motor—constantly sliding, sealing, and converting compressed air into rotation. Over time they wear down, lose sealing efficiency, and your drill starts feeling weak, sluggish, or inconsistent. Th..

Reversible pneumatic drill The pneumatic drill is ideal for drilling in a production line. The drill has non-variable speed set to 550 rpm. A compressor is required with an air flow delivery of at least 170 l/min at 6.3 Bar to make use of the drill. Make sure that an in-line lubricator is fitted with pneumatic oil (AT OIL).....